Parts & Accessories

Sticks Like $%*? To a Blanket! Self-adhesive computer mount using 3M VHB tape (very high bond) Designed to fit onto your top tube behind your stem for maximum protection and less distraction. Flat for flat top tubes with a minimum of 26mm wide flat area. If the top tube has a curve of more than 2mm over the 26mm then Flex is your best bet. Flex for round and non-flat top tubes. for narrow round tubes of 35mm and lower will require some clamping in place to ensure a good bond. Supplied with alcohol wipe to clean the area to be attached to. Manufactured in-house using our Multi Jet Fusion industrial 3D printer then shot peened for surface toughness and quality. Recommended for smaller series computers no larger than Wahoo Element Roam, Garmin 500 series. As with any mount we recommend using the looping the lanyard IMPORTANT - Check there is clearance from the underside of bars/stem to the top tube. SEE CLEARANCE DIAGRAM Sticks to Invisframe and AMS frame protection - others not tested. To remove pry the mount off from one end. The adhesive pad should remain in one piece but cannot be reused. Replacement VHB pads are available here. It helps to heat with a hairdryer or leave in a warm room beforehand.

Bosch SmartphoneHub USB Cap, For protecting the bearing L1 und L3 on the drive unit. The SmartphoneHub transforms your bike into a fully networked eBike. The smartphone and COBI.Bike app turn the SmartphoneHub into an intelligent control center that can be used for navigation, recording activities, and connection to other. The eBike can also be ridden without a smartphone due to the integrated display in the SmartphoneHub, showing the most important riding data. - The SmartphoneHub and the COBI.Bike app connect the eBike to the digital world and allow for navigation, music streaming, fitness tracking, and integration of other services and apps such as Strava - A 1.52-inch display allowing for use without a smartphone - The COBI.Bike app gives eBikers a permanent overview of the most important training data. such as performance, cadence and calorie consumption - The COBI.Bike app allows access to music and audiobook streaming services, such as Spotify or Audible, which can be operated by remote control - The SmartphoneHub charges phones using the eBike battery - Walk assistance function helps you push your eBike at speeds of up to 6 mph

The SmartphoneHub transforms your bike into a fully networked eBike. The smartphone and COBI.Bike app turn the SmartphoneHub into an intelligent control center that can be used for navigation, recording activities, and connection to other. The eBike can also be ridden without a smartphone due to the integrated display in the SmartphoneHub, showing the most important riding data. - The SmartphoneHub and the COBI.Bike app connect the eBike to the digital world and allow for navigation, music streaming, fitness tracking, and integration of other services and apps such as Strava - A 1.52-inch display allowing for use without a smartphone - The COBI.Bike app gives eBikers a permanent overview of the most important training data. such as performance, cadence and calorie consumption - The COBI.Bike app allows access to music and audiobook streaming services, such as Spotify or Audible, which can be operated by remote control - The SmartphoneHub charges phones using the eBike battery - Walk assistance function helps you push your eBike at speeds of up to 6 mph

The SmartphoneHub transforms your bike into a fully networked eBike. The smartphone and COBI.Bike app turn the SmartphoneHub into an intelligent control center that can be used for navigation, recording activities, and connection to other. The eBike can also be ridden without a smartphone due to the integrated display in the SmartphoneHub, showing the most important riding data. - The SmartphoneHub and the COBI.Bike app connect the eBike to the digital world and allow for navigation, music streaming, fitness tracking, and integration of other services and apps such as Strava - A 1.52-inch display allowing for use without a smartphone - The COBI.Bike app gives eBikers a permanent overview of the most important training data. such as performance, cadence and calorie consumption - The COBI.Bike app allows access to music and audiobook streaming services, such as Spotify or Audible, which can be operated by remote control - The SmartphoneHub charges phones using the eBike battery - Walk assistance function helps you push your eBike at speeds of up to 6 mph

The SmartphoneHub transforms your bike into a fully networked eBike. The smartphone and COBI.Bike app turn the SmartphoneHub into an intelligent control center that can be used for navigation, recording activities, and connection to other. The eBike can also be ridden without a smartphone due to the integrated display in the SmartphoneHub, showing the most important riding data. - The SmartphoneHub and the COBI.Bike app connect the eBike to the digital world and allow for navigation, music streaming, fitness tracking, and integration of other services and apps such as Strava - A 1.52-inch display allowing for use without a smartphone - The COBI.Bike app gives eBikers a permanent overview of the most important training data. such as performance, cadence and calorie consumption - The COBI.Bike app allows access to music and audiobook streaming services, such as Spotify or Audible, which can be operated by remote control - The SmartphoneHub charges phones using the eBike battery - Walk assistance function helps you push your eBike at speeds of up to 6 mph

The SmartphoneHub transforms your bike into a fully networked eBike. The smartphone and COBI.Bike app turn the SmartphoneHub into an intelligent control center that can be used for navigation, recording activities, and connection to other. The eBike can also be ridden without a smartphone due to the integrated display in the SmartphoneHub, showing the most important riding data. - The SmartphoneHub and the COBI.Bike app connect the eBike to the digital world and allow for navigation, music streaming, fitness tracking, and integration of other services and apps such as Strava - A 1.52-inch display allowing for use without a smartphone - The COBI.Bike app gives eBikers a permanent overview of the most important training data. such as performance, cadence, and calorie consumption - The COBI.Bike app allows access to music and audiobook streaming services, such as Spotify or Audible, which can be operated by remote control - The SmartphoneHub charges phones using the eBike battery - Walk assistance function helps you push your eBike at speeds of up to 6mph

The SmartphoneHub transforms your bike into a fully networked eBike. The smartphone and COBI.Bike app turn the SmartphoneHub into an intelligent control center that can be used for navigation, recording activities, and connection to other. The eBike can also be ridden without a smartphone due to the integrated display in the SmartphoneHub, showing the most important riding data. - The SmartphoneHub and the COBI.Bike app connect the eBike to the digital world and allow for navigation, music streaming, fitness tracking, and integration of other services and apps such as Strava - A 1.52-inch display allowing for use without a smartphone - The COBI.Bike app gives eBikers a permanent overview of the most important training data. such as performance, cadence and calorie consumption - The COBI.Bike app allows access to music and audiobook streaming services, such as Spotify or Audible, which can be operated by remote control - The SmartphoneHub charges phones using the eBike battery - Walk assistance function helps you push your eBike at speeds of up to 6 mph

The SmartphoneHub transforms your bike into a fully networked eBike. The smartphone and COBI.Bike app turn the SmartphoneHub into an intelligent control center that can be used for navigation, recording activities, and connection to other. The eBike can also be ridden without a smartphone due to the integrated display in the SmartphoneHub, showing the most important riding data. - The SmartphoneHub and the COBI.Bike app connect the eBike to the digital world and allow for navigation, music streaming, fitness tracking, and integration of other services and apps such as Strava - A 1.52-inch display allowing for use without a smartphone - The COBI.Bike app gives eBikers a permanent overview of the most important training data. such as performance, cadence and calorie consumption - The COBI.Bike app allows access to music and audiobook streaming services, such as Spotify or Audible, which can be operated by remote control - The SmartphoneHub charges phones using the eBike battery - Walk assistance function helps you push your eBike at speeds of up to 6 mph

The Bosch Purion is a minimalist on-board computer designed for anyone who wishes to focus on the most important information and prefers an uncluttered handlebar. The Purion displays the essentials and lets riders get all important information with a click of the thumb, while keeping hands on the handlebars. Five different riding modes provide just the right amount of assistance in every situation. - Manages four levels of assist from Eco to Turbo, with an eMTB mode specially designed for the Performance Line CX Drive system - Features include charging status, speed, riding mode, range, trip distance and total distance

The SmartphoneHub transforms your bike into a fully networked eBike. The smartphone and COBI.Bike app turn the SmartphoneHub into an intelligent control center that can be used for navigation, recording activities, and connection to other. The eBike can also be ridden without a smartphone due to the integrated display in the SmartphoneHub, showing the most important riding data. - The SmartphoneHub and the COBI.Bike app connect the eBike to the digital world and allow for navigation, music streaming, fitness tracking, and integration of other services and apps such as Strava - A 1.52-inch display allowing for use without a smartphone - The COBI.Bike app gives eBikers a permanent overview of the most important training data. such as performance, cadence and calorie consumption - The COBI.Bike app allows access to music and audiobook streaming services, such as Spotify or Audible, which can be operated by remote control - The SmartphoneHub charges phones using the eBike battery - Walk assistance function helps you push your eBike at speeds of up to 6 mph

Bosch Aftermarket Kit Smartphone Hub, with 1500mm DU-cable, Universal Mount and Compact Remote and Mounting Parts. The SmartphoneHub transforms your bike into a fully networked eBike. The smartphone and COBI.Bike app turn the SmartphoneHub into an intelligent control center that can be used for navigation, recording activities, and connection to other. The eBike can also be ridden without a smartphone due to the integrated display in the SmartphoneHub, showing the most important riding data. - The SmartphoneHub and the COBI.Bike app connect the eBike to the digital world and allow for navigation, music streaming, fitness tracking, and integration of other services and apps such as Strava - A 1.52-inch display allowing for use without a smartphone - The COBI.Bike app gives eBikers a permanent overview of the most important training data. such as performance, cadence and calorie consumption - The COBI.Bike app allows access to music and audiobook streaming services, such as Spotify or Audible, which can be operated by remote control - The SmartphoneHub charges phones using the eBike battery - Walk assistance function helps you push your eBike at speeds of up to 6 mph

Versatile and clever The Nyon is the perfect companion for embarking on your fully connected eBike experience. Nyon connects to your smartphone with the eBike Connect app and exchanges data about routes and activities. The color display serves as an intelligent guide when you are exploring new places and as your personal trainer by providing you with fitness data. The touch screen makes the all-in-one computer both intuitive and easy to use and is operated using the separate control unit during your ride. Whether you're using your eBike for long rides or short everyday trips, the robust, easy-to-read display ensures that you are ready for all requirements and weather conditions. The Nyon computer – for a smarter, more intuitive and connected generation. This is what Connected Biking feels like. Simple operation A convenient option: Nyon is intuitive to use thanks to the touch screen function and can be operated using the separate control unit during your ride. Award-winning design Impressive both inside and out: The 3.2-inch high-resolution color display combines smart functions with an elegant design that has won a Red Dot Design Award. Easy to read A clear view in any light: The display brightness and backlight automatically adapt to the ambient light. A special coating reduces glare and finger marks. You can choose between a dark and a bright display with maximum contrast. Individual screens Focus on the essential: You can customize the user interface of the display to suit your specific requirements. This gives you a clear view of the information that you need at all times. Always ready for action Whatever the weather: The touch screen of the robust display remains fully functional even when exposed to rain or dust and can be operated while wearing bike gloves. Savings Screen If you want to find out how much you could save by choosing to use your eBike instead of a car, check out the info on the new Savings Screen. This is activated in the screen management settings. You can also see a comparison of the current and previous weeks, or choose a different currency in the settings. Smart connectivity functions Perfectly connected: Nyon is part of an intelligently connected system and opens the door to the connected eBike World of Bosch thanks to the eBike Connect smartphone app and an online portal. Data synchronization Constant communication: As soon as Nyon connects to your smartphone or Wi-Fi, the computer connects to your eBike Connect account and automatically synchronizes the riding data. Choose your ideal position Optimum position: To ensure the best possible readability, the display mount has two installation positions. The center mounting position above the handlebar is designed to meet the needs of eMTB riders, while tour riders can place the mount further forward. One device, several users One for all: You can share your Nyon with friends or family – everyone can then synchronize their riding data with their own account. Software updates Always up-to-date: Software updates or new maps can be conveniently downloaded and installed over the air.

Accessory Mount from Cane Creek.

Cane Creek is proud to introduce an ultra-premium computer mount that is intuitive and easy to use. The Cane Creek Computer Mount is incredibly modular with 4 mounting orientations, several angle adjustments and compatibility to run an accessory mount. Every computer mount comes with a Garmin and Wahoo adapter and ability to run an accessory mount. The accessory mount is sold separately and has compatibility to run lights or a camera. Cane Creek's Computer Mount is made with 6061CNC Aluminum and Stainless Steel Black bolts.

Seamlessly connected. This SP Connect kit allows any smartphone case to be connected to the Intellimount Stem for a tidy dashboard on your bike. Highlights: - Fits most smartphone cases - Includes Intellimount adapter, adhesive mount and stand tool - Compatible with all SP products

OEM CR2032 3V Lithium Battery used in most CatEye cycle computers.

Cadence Magnet for all CatEye computers that record cadence.

Wheel magnet for all CatEye cycle computers

- Handlebar mount for CatEye wired computers - Compatible with Velo 7 and Velo 9

- Dual-band Bluetooth and ANT+, magnetless sensor with integrated accelerometer - Quick pairing with CatEye Cycling app (Bluetooth) - Waterproof IPX7 (based on JIS C0920) - Works with Padrone Digital, Padrone Smart+, Padrone Smart*, and Strada Smart* *For Padrone Smart and Strada Smart, works in Mirror Mode only

CatEye's Bluetooth Speed/Cadence Sensor transmits your speed and cadence through your Bluetooth-compatible Smartphone to your handlebar-mounted CatEye Strada Smart cyclo-computer (sold separately). Download the CatEye Cycling app for iPhone/Android and you’ll get all your ride data and save your phone battery. Attack each ride and celebrate your successes on the bike!

The BlueGiga dongle gives Rouvy, CycleOps' virtual training software, the ability to seamlessly connect to Bluetooth devices and sensors. The BlueGiga dongle contains a Bluetooth (BLE) radio that allows PCs to communicate with BLE devices, including CycleOps smart indoor bicycle trainers and power meters made by the folks at PowerTap. Most importantly, the BlueGiga dongle is necessary to update the firmware Over the Air (OTA) via VirtualTraining for the Hammer and Magnus bike trainers. - Bluetooth dongle for PCs to work with Rouvy - Needed for Over the Air Firmware Updates to Smart Indoor Bike Trainers. - Works with PC desktops and laptops.

Mount your Garmin Edge computer with the Quarter Turn Bike Mount. It includes the bike mount, rubber disc, and elastic bands to secure the Quarter Turn to your stem or handlebars.

Garmin's Bicycle Mount Kit lets you attach any compatible Garmin to your bike's handlebars, so the data stays out in front where you can see it.

Protective Silicone case for Edge 1040 and 1040 Solar

Mount your Varia Rearview Radar or Varia Smart Bike Light (each sold separately) to the seat post of a second bike with this quarter-turn mount. Includes mount and 2 fitting shims.

Mount your Varia Rearview Radar or Varia Smart Bike Light (each sold separately) to an aero or round seat post with this quarter-turn mount. Includes mount, 2 fitting shims and 4 O-rings.

- USB-A Edge Power Mount Cable - 400mm

Monitor your speed as you ride with this easy-to-install wireless sensor. With no magnets or other exposed parts to line up, this sensor is easy to install, maintain and move between bikes. The speed sensor 2 attaches to the hub of either wheel. You can set up wheel size in our Garmin Connect online community or self-calibrate with an Edge cycling computer or compatible Garmin device. Once set up, you’ll get accurate speed and distance at all times — even without a head unit. ANT+ connectivity and BLUETOOTH Low Energy technology let you sync to Garmin Connect and other training apps, compatible devices and fitness equipment for better data when you ride indoors and outdoors.

Monitor your pedaling cadence as you ride with this easy-to-install wireless sensor. With no magnets or other exposed parts to line up, this sensor is easy to install, maintain and move between bikes. Simply attach the sensor and ride. With no magnets or other exposed parts to line up, this sensor is easy to install, maintain and move between bikes.

Stay ahead of the pack with Garmin's Extended Out-front Bike Mount that lets you to take full advantage of your Edge's capabilities without compromising your ride. The mount positions your device for easier monitoring and safety. Also compatible with the Forerunner 910XT and 310XT when used with a quick-release kit (sold separately).

Stay ahead of the pack with Garmin's Out-front Bike Mount that lets you to take full advantage of your Edge's capabilities without compromising your ride. The mount positions your device for easier monitoring and safety. Also compatible with the Forerunner 910XT and 310XT when used with a quick-release kit (sold separately).

Monitor your speed and cadence as you ride with these easy-to-install wireless sensors. With no magnets or other exposed parts to line up, these sensors are easy to install, maintain and move between bikes. The speed sensor 2 attaches to the hub of either wheel and self-calibrates with your Edge cycling computer or compatible Garmin device to give you accurate speed and distance at all times — even without a head unit. The cadence sensor 2 fastens to any size crank arm and measures pedal strokes per minute so you can get the most out of your training. Send live speed, distance and cadence data to compatible training apps or displays by using ANT+ connectivity and BLUETOOTH Low Energy technology. With both of these sensors on your bike, you can work to improve your personal best or see where you stand against the pros.

Computes and Transmits Meaningful Data - Computes and sends 6 running dynamics metrics to your compatible device - Battery life: replaceable battery lasts up to 1 year (assuming 1 hour daily use) - Automatically turns itself on and off - Tiny size: at less than 0.5 ounces, you'll forget it's there - Compatible devices connect with the Garmin Connect Mobile app to automatically sync your data and connect with others Train Hard, Run Free The Running Dynamics Pod easily clips onto your waistband to measure the running dynamics you need to beat yesterday. It gives you the option to run without a heart rate monitor chest strap. Once paired with your compatible smartwatch, just clip it to the back and center of your waistband and start your run. Review Your Form View and analyze important running metrics such as your cadence, stride length, ground contact time and balance, vertical oscillation and vertical ratio. These biomechanical measurements can help you understand your running form so you can perform better on race day. How It Works: The Running Dynamics Pod has an accelerometer in the module that measures torso movement to calculate these 6 running metrics: - Cadence is the number of steps per minute. It displays the total steps (right and left combined). - Ground contact time balance displays the left/right balance of your ground contact time while running. It displays a percentage. For example, 53.2 with an arrow pointing left or right. - Stride length is the length of your stride from 1 footfall to the next. It is measured in meters. - Vertical oscillation is your bounce while running. It displays the vertical motion of your torso, measured in centimeters for each step. - Vertical ratio is the ratio of vertical oscillation to stride length. It displays a percentage. A lower number typically indicates better running form. - Ground contact time is the amount of time in each step that you spend on the ground while running. It is measured in milliseconds.

Edge Power Mount - Computers Parts and Accessories

Stay aware of approaching cars with Varia RTL515 rearview radar. It pairs with your Edge bike computer or compatible smartphone to alert you of vehicles approaching from behind up to 153 yards (140 meters) away. When used with your compatible smartphone, the Varia app uses bold graphics — plus tone and vibration alerts — to indicate the position and speed of approaching vehicles. MAXIMUM AWARENESS - Varia RTL515 rearview radar provides visual and audible alerts for vehicles approaching from behind up to 153 yards (140 meters) away. MULTIPLE PAIRING OPTIONS - This radar works seamlessly with your Edge bike computer or compatible smartphone as well as select Garmin wearables or the optional radar display unit. WORKS WITH THE VARIA APP - This smartphone app helps you increase your awareness by providing graphics — plus tone and vibration alerts — that indicate the position and speed of approaching cars. THIRD-PARTY APP COMPATIBLE - When used with a compatible smartphone, Varia radar integrates with your favorite apps, such as Ride with GPS to overlay your maps with rearview radar alerts. SUPERIOR VISIBILITY - Alert motorists to your presence as soon as possible with daylight visibility up to 1 mile. COMPACT DESIGN - Easily mount this sleek, compact device on the seatpost of almost any road-use bicycle. The vertical design allows for better leg clearance and a perfectly comfortable ride. PELOTON MODE - Varia RTL515 features multiple modes, including peloton mode, which provides a low-intensity flash that is kind to other cyclists’ eyes when riding in a group. BATTERY LIFE - Time spent charging is not as good as time spent riding. Get up to 16 hours of battery life in day flash mode and up to 6 hours in solid mode. Physical Specifications - Dimensions: 3.9” x 0.8” x 1.6" (98.6 x 19.7 x 39.6 mm) - Weight: 2.5 oz (71.0 g) - Modes: solid, peloton, night flash, day flash - Lumens: 20 solid, 8 peloton, 29 night flash, 65 day flash - Battery life: 6 hours solid, 8 hours peloton, 6 hours night flash, 16 hours day flash - ANT+: Yes - BLE: Yes - Water rating: IPX7 - Viewing angle: 220° In the box: - Varia RTL515 - Mounting Kit - Cables - Documentation

It’s got your back while you ride ahead. Varia™ eRTL615 rearview radar for eBikes is our first battery-free radar. It plugs directly into your compatible eBike. It detects cars approaching from behind and provides audible and visible alerts when paired with your compatible Garmin smartwatch, bike computer or even your smartphone with the Varia™ app. This radar also has a bright tail light to make you more visible to motorists, adding peace of mind to every ride. And since you don’t have to charge it between rides, that’s one less thing to worry about.

Lights, Camera, You Name it The Accessory Mount is a great solution for attaching your GoPro-style mount to your helmet, seatpost, handlebar, selfie-stick or just about anything else. The banded system offers easy attachment, the 270 degree rotation helps you position your camera so that you can get the shot every time, and the omni-directional breakaway feature will take the hit in a crash (possibly saving your camera equipment). With the Accessory Mount, your imagination is the only thing holding you back. Features - Omni-directional breakaway, 270 Degree Rotation

This NiteRider Adapter is sold separately from K-EDGE “Combo Mount." - Precision Machined 6061-T6 Aluminum - Anodized Gunmetal - Converts a NiteRider Rail Interface to adapt K-Edge GoPro Mounting Interface - Enables compatibility with K-Edge GoBig Mounts and Combo Mounts - 2x M4 Mounting bolts with Nylok included - Compatible with Lumina Series, Mako Series - Weight: 11.5 grams

The K-EDGE Gravity Top Cap is a great computer mount for those mountain riders that already a lot going on with the cockpit of their bikes, or just want a simple and sleek looking computer mount. The Top Cap replaces your already existing top cap with the K-EDGE Gravity top cap. Ideal position for Downhill and Enduro racing/riding, but is also a popular solution for any bike when using a smaller style computer (20, 25, 200, 500, 510, 520, 820). - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Garmin Specific Co- Polymer Interface - Compatibility: All Garmin Edge® Computers including the 1030*, 1000*, 820, 810*, 800*, 510, 520, 500, 200, 25, 20. Also supports the Touring, Touring Plus, Forerunner 310XT, and 910XT. (Larger EDGE computers such as 800, 810, 1000, 1030 may interfere with very steep, upright, stem angles.) - Made in Boise, Idaho, USA. - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded.

The K-EDGE Gravity Cap is a great computer mount option for those riders that already a lot going on with the cockpit of their bikes, or just want a simple and sleek computer mount. The Gravity Cap replaces your existing top cap and is ideal for Downhill, Enduro, Gravel, Touring, etc. - CNC Machined 6061-T6 Aluminum - Injection Molded Copolymer Interface - Compatibility: Wahoo ELEMNT - Lifetime Warranty - Weight: 18g - Anodized Colors: Black

The K-EDGE Garmin Stem Mount is a great upgrade solution for cyclists who prefer their computer above the stem. Mounting off of the steerer tube, the mount replaces a standard 5mm spacer, and is locked securely in place by the top cap compression system. The adjustable version allows for a variety of different stem angles. Can be used with positive or negative degree stems and additional spacers can be added (5mm to 10mm) above the stem. Note that some of the larger computers will not always work with a steep angled stem. Designed with mountain biking in mind, the K-EDGE Stem mount is also ideal for much more including: cyclocross; triathlon; bike touring; or if you simply prefer this position for your computer.

K-EDGE’s legendary CNC machined aluminum quality and strength for the price conscious cyclist. Pro positioning of your computer, out-front and flush with the top of the handlebar. - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Copolymer Interface - Compatibility: Wahoo Bolt - Fits Handlebars: 31.8MM - NOT GoPro Interface Compatible - Anodized Color: Black Please contact K-EDGE warranty manager Info@K-EDGE.com for questions or concerns. We highly suggest you follow the recommendations in the Sigma instructions that recommend use of the provided tether leash.

The Top Tube Mount places your computer front and center on the top tube of Gravel, MTB, and Adventure Bikes with preset mounting positions. - Compatible with all Garmin cycling computers - Multi-mount positions - Garmin approved insert protects the computer body tabs in the event of a crash - All hardware included - CNC machined in Boise, Idaho USA - Made in USA - Lifetime warranty

An excellent choice for mountain, cross, and road cyclists who prefer to have the computer above the stem. The mount replaces a standard 5mm spacer and is locked securely in place by the top cap compression system. - Supported Computers – Wahoo ELEMNT, Wahoo Bolt, Wahoo MINI - Compatible – 1-1/8" Steerer tube Diameter, - Thickness: 5mm, Length 50mm (Center-to-Center) - Recommended for 0 Degree to Negative Degree Stem Angles - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Copolymer Interface - Weight: 25g - Made in Boise, Idaho, USA - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded

A simple, lightweight and versatile mount for positioning the Wahoo ELEMNT between the aero bars. Single bolt clamp and pivoting mount design. - For 22.2mm diameter aero bar extensions - Compatible with Wahoo ELEMNT, Wahoo Bolt, Wahoo MINI - Combo Compatible with use of adapter for GoPro style interface action camera and lights - Replaceable Wahoo insert - Weight: 29g - Anodized Colors: Black - Made in Boise, Idaho, USA - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded

- CNC Machined Aluminum - Combo Compatible (580 Add-On sold separately) - WAHOO approved replaceable computer insert protects computer tabs - Anodized Black with laser etched logos - Payload Capacity: Top 123g / Bottom 242g with combo adapter - Weight: 47g - Mount Type: Clamp 31.8mm - Mount Weight: 47g Compatibly: - WAHOO BOLT and MINI (ROAM users choose MAX XL K13-4605) - Combo (GoPro-style light/camera interface) adapter compatible (K13-580-BLK sold separately)

- Ideal fit for very short stems with steep upward stem angles - 1cm rise in the base will allow larger cycling computers like the Garmin 1030 to nest securely above the stem without interference

An excellent choice for mountain, cross, and road cyclists who prefer to have the computer above the stem. - Far and away more advanced than the plastic options on the market - Boost Stem Mount is specifically designed to fit atop the shortest stems on the market today - The Gravity Cap replaces your existing top cap and is ideal for Downhill, Enduro, Gravel, Touring, etc - The mount replaces a standard 5mm spacer and is locked securely in place by the top cap compression system - Compatibility: Wahoo ELEMNT, Wahoo Roam, Wahoo Bolt, Wahoo MINI - CNC-machined aluminum for low weight and strength - Made in the USA with a lifetime warranty - Stem mount that is for short, steep stem angles boosting the computer up above by 1cm

- CNC Machined Aluminum - Combo Compatible (K13-580 adapter sold separately) - GARMIN approved replaceable computer insert protects computer tabs - Anodized Black with laser etched logos - Payload Capacity: Top 123g / Bottom 242g with combo adapter - Weight- 47g Compatibility: - GARMIN Cycling Computers smaller than EDGE 1000, 1030 style (example EDGE 820) - Combo compatible (GoPro-style light/camera interface) K13-580-BLK adapter sold separately

- CNC Machined Aluminum - Combo Compatible (K13-580 adapter sold separately) - GARMIN approved replaceable computer insert protects computer tabs - Anodized Black with laser etched logos - Payload Capacity: Top 123g / Bottom 242g with combo adapter - Weight- 50g Compatibility: - All Garmin Cycling Computers - Combo (GoPro-style light/camera interface) adapter compatible (K13-580-BLK sold separately)

- CNC Machined Aluminum - Combo Compatible (580 Add-On sold separately) - WAHOO approved replaceable computer insert protects computer tabs - Anodized Black with laser etched logos - Payload Capacity: Top - 123g / Bottom 242g with combo adapter - Weight: 50g - Mount Type: Clamp 31.8mm - Mount Weight: 53g Compatibly: - All Wahoo Cycling Computers- ROAM, BOLT, ELEMNT, MINI - Combo compatible (GoPro-style light/camera interface), K13-580-BLK adapter sold separately

The NEW K-EDGE Computer Mount for the NEW Wahoo Bolt is the most secure cycling computer mount available. Lock your Bolt in place with confidence. Aero design flush with the top of the handlebar. - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Copolymer Interface - Compatibility: Wahoo Bolt, Wahoo Mini - Fits Handlebars: 31.8MM - Go Pro Action Camera type attachment for camera or light - Anodized Color: Black - Made in Boise, Idaho, USA - Lifetime Guarantee against material or manufacturer defects. Damages due to abuse or crashing excluded. * Attention: ASSEMBLY BOLTS NOT MEANT TO BE REMOVED OR TAMPERED WITH AT ANY TIME. The torx head bolts are installed using a permanent thread-lock compound. Doing so will void all warranties. K-EDGE Combo Mount are NOT DESIGNED to hold a Cycliq Fly 12. (Cycliq Fly 12 & Fly12CE users should choose the K-EDGE K13-410, K13-420, K13-2450 GO BIG camera/light mounts.) Please contact K-EDGE warranty manager Info@K-EDGE.com for questions or concerns. We highly suggest you follow the recommendations in the Sigma instructions that recommend use of the provided tether leash.

At 32 Grams the Race Mount is 33% lighter than the “standard” Wahoo Mount. - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Copolymer Interface - Compatibility: Wahoo Bolt, Wahoo Mini - Fits Handlebars: 31.8MM - NOT GoPro Compatible - Anodized Color: Black - Made in Boise, Idaho, USA - Lifetime Guarantee against material or manufacturer defects. Damages due to abuse or crashing excluded. * Attention: ASSEMBLY BOLTS NOT MEANT TO BE REMOVED OR TAMPERED WITH AT ANY TIME. The torx head bolts are installed using a permanent thread-lock compound. Doing so will void all warranties. Please contact K-EDGE warranty manager Info@K-EDGE.com for questions or concerns. We highly suggest you follow the recommendations in the Sigma instructions that recommend use of the provided tether leash.

- CNC Machined Aluminum - Combo (Computer on top – light or camera underneath) - WAHOO approved replaceable computer insert protects computer tabs - Anodized Black with laser etched logos - Payload Capacity: Top - 123g / Bottom 242g on K-EDGE K13-580 Combo adapter - Weight: 60g - Mount Type: Clamp 31.8mm - Mount Weight: 60g Compatibly: - All WAHOO Cycling Computers – ROAM, BOLT, ELEMNT, MINI

- CNC Machined Aluminum - Combo Compatible (580 Add-On sold separately) - WAHOO approved replaceable computer insert protects computer tabs - Anodized Black with laser etched logos - Payload Capacity: Top - 123g / Bottom 242g - Weight: 63g - Mount Type: Clamp 31.8mm - Mount Weight: 53g Compatibly: - All Wahoo Cycling Computers- ROAM, BOLT, ELEMNT, MINI - Combo (GoPro-style light/camera interface) K13-4500-31.8-BLK

The K-EDGE Garmin TT Mount is the most advanced Time Trial and Triathlon computer mount available. Featuring a twist-lock mechanism to lock your Garmin with confidence. The K-EDGE Garmin TT Mount’s aluminum design and its unique locking feature is by far the most advanced mount on the market. With traditional TT mounts for the Garmin computer, you have to either have enough room between the extensions to perform the ¼ turn “twist” or the computer has to be mounted above the extensions. - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Copolymer Interface - Compatibility – 22.2mm diameter TT Extensions - Supported Computers – Garmin Edge 20, 25, 200, 500, 510, 520*, 800, 1000, and Forerunner 310XT - Made in Boise, Idaho, USA - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded. *Garmin 520 is not compatible at this time.

- CNC machined 6016-T6 aluminum platform, injection molded copolymer interface - Compatibility: Wahoo Bolt, Wahoo Mini - Fits 31.8mm handlebars - Weight: 38g - Lifetime guarantee against material or manufacturer defects. Damages due to abuse or crashing excluded

- Compatible with Wahoo Roam computer - CNC machined aluminum - Includes lockable set screw, replaceable insert - Aerodynamic fit - 31.8mm clamp - Mount Weight: 48g

KMC's digital ChainChecker is the most accurate tool for checking your chain’s elongation. - Measures up to 2.5mm elongation - Fits all chains including 11 speed - Handy electronic device - Stainless hardened metal body