Wheels

Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP. It includes the following: - Threaded axle spacer M12 x 1.75 Coarse - M12 x 1.5 Medium - M12 x 1.0 Fine - End Cap

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

Don't let a bent or worn dust cap sully an otherwise well-functioning Shimano Alfine internally geared hub. Get a spare and replace as necessary for continued performance and to preserve the longevity that you expect from Alfine.

- Soft and elastic for an easy mounting - Resistance to high pressure: 8 bar / 116 psi - High resistance to punctures - Sold by the unit

- Soft and elastic for an easy mounting - Resistance to high pressure: 8 bar / 116 psi - High resistance to punctures - Sold by the unit

Schwalbe High Pressure Rim Tape effectively protects the tube against mechanical damage. - Elastic for ease of installation - High pressure: 8 bar / 116 psi

Keeping that well-functioning Shimano Alfine internally geared hub in top working condition means keeping the internals clean. Replace the left hub seal ring when necessary for continued performance and to preserve the longevity that you expect from Alfine.

Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.

Sold by the unit

Do you need to replace the right lock washer seal on your Alfine SG-S700 internally geared hub? If you're not sure, it might not be a bad idea, as contamination from damaged or worn seals is the kryptonite of virtually maintenance-free internally geared hubs.

Keeping contamination out of your internally geared hub is critical to its function and longevity. Sometimes, the oil port bolt comes loose and it's easy to lose, even if you've just taken it out to oil your hub. Keep a spare or two so your hub stays clean inside and it'll last you many, many miles.

Our 2Bliss Ready Rim Strips create a secure barrier from sealant to rim in a clean simple to install strip. Riders running 2Bliss can now change tires quicker and easier than with any other tubeless system.

- High performance adhesive tape, a great pairing with Velox Cement - Each roll is usually adequate for gluing two tubular tires - Protects tube from spoke/nipple/rim puncture

Pack of 30 ornaments. - 5 different colors - Fits all standard spoke diameters

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set. - DT 350 20x110mm Left Dust Cap

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

This lightweight, high-pressure rim tape offers great protection against spoke hole flats and is easy to install. This Italian-made tape is light and thin, so it will not inhibit tire fitting. Nylon elastic material is used to ensure a snug fit without movement.

New cones make hubs spin like silk. Take advantage of your Shimano Alfine hub's highly serviceable design, and replace the bearing cones if they are worn or damaged. This one is specifically for the right side.

Replacement Pawls for all Oozy hubs.

Replacement springs and pawls. Includes 6 pawls, 6 springs and 1 plastic retaining ring that holds the pawls in place even during disassembly to ensure you're never searching the floor for tiny springs.

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Rear 10mm x 1 axle - Shimano Right Rear Cone - Cone Wrench Size: 15mm - Threads: 10mm x 1 - Diameter: 17.0mm - Length: 9.0mm - 1 cone per bag COMPATIBLE HUBS: - XT M750, 9-spd Rear - XT M760, 9-spd Rear - XT M765, 9-spd Rear - Deore LX M570, 9-spd Rear

Grade 10 chromium steel balls

- Extra long quick release for rear axle mount rack systems

Replacement bearings and bushings specific to Spoon 90 (Small) and 100/110 (Medium and Large) pedals. Eliminates play that can develop over time, and revives performance. Includes: - Sealed Bearing x2pcs - 10mm IGUS Bushing x2pcs - Green Friction Seal x2pcs - Locknut - O-ring x 2pcs

Aluminum Tubeless Presta Valve - MTB or Road

Aluminum Tubeless Presta Valve - MTB or Road - 18-25mm for Asymmetric Rims

Aluminum Tubeless Presta Valve - MTB or Road - 18-25mm for Cylindrical Rims

Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.

- Replacement straight pull spokes for Zipp 88 (Front) and 188 (Rear) Hubs