Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Parts & Accessories

$119.99
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
$115.00
- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap
$112.00
- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Right Axle End Cap
$109.99
- Designed to stabilize 15g spokes in most hub flanges - 1000-pack
$107.99
Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP. It includes the following: - Threaded axle spacer M12 x 1.75 Coarse - M12 x 1.5 Medium - M12 x 1.0 Fine - End Cap
$106.99
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$104.00
Original equipment freehub bodies to fit SRAM hubs and wheels.
$104.00
Replacement freehub body for Sram 900 series hubs
$99.99
Dynaplug Air is the only tool of it's kind in the world. Plug your tubeless Mountain/Gravel tire and quickly air it up with CO2 at the same time! Here's how it works: 1) Insert repair nozzle into puncture. 2) Open regulated air valve to achieve desired pressure. 3) Close valve and remove tool. Plug will hold air and seal puncture simultaneously. Dynaplug Air Kit includes: - Insertion Tube for MTB/Gravel (25mm length) - x4, Brass soft nose tip repair plugs, for Mountain/Gravel tires only - Neoprene pouch - CO2 hose for valve stem (CO2 cartridges are NOT included) Please note—the MTB tire Plugs are about twice the length of the Road style plug. So the MTB tire plugs should not be used for Road tire repairs.
$99.99
Get rolling again with a replacement freehub body for your Mavic wheels. - For Mavic ID 360 hubs
$29.99 - $94.99
- Grade 3 balls and magnetite rust proof finish - Abec 5 precision and silicone w seals - 3 times cryogenic race treatment - Bearings sold individually, not as pair
$94.99
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
$94.99
Shimano, FH-M828/788/678/648, Freehub body, Y3TH98050
$94.49
The Muc-Off Ultimate Tubeless Kit contains everything needed to get a tubeless-ready wheelset set up and ready to roll. Each Kit contains Tubeless Rim Tape, two CNC-machined black tubeless valves and two pouches of No Puncture Hassle Tubeless Sealant.
$92.99
Make it more aerodynamic – this nipple is hidden inside the rim. DT Hidden Nipples are designed for high-profile rims, in which the inverted design is essential for optimum precision. They are very light and hidden on the inside of the rim: perfectly suited for high aero wheels. The nipples will align perfectly due to their spherical contact surface. - Weight: 22g for 64 nipples
$92.99
The buyer's choice for wheel builders looking to save weight. ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond. - Weight: starting at 20g for 64 nipples
$41.99 - $92.99
Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.
$88.00
Fully connected. Connect with your ride. Integrated Cannondale wheel sensor, co-developed with Garmin, delivers hyper accurate speed, route and distance info, registers your bike, reminds you of needed service and more, all through the free Cannondale App. Highlights: - Captures essential ride data automatically - Includes adapters for most wheel types - Utilizes the Cannondale App for ultimate connectivity
$87.00
Maxle Ultimate Lever Assembly - Fits Maxle Ultimate B1 - Includes lever section only - Suitable for suspension forks
$84.99
Get rolling again with a replacement 10-speed freehub body for Mavic wheels.
$82.99
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
$79.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Conical X12 washer, compatible with Syntace X-12 system - Removable, plug-in lever design is streamlined and protects your RWS lever - Thread Pitch: 12 x 1.0mm
$79.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Removable, plug-in lever design is streamlined and protects your RWS lever
$27.59 - $79.99
The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples
$79.99
Tannus Armour Tubeless inserts are the result of years of top level multi-cell foam manufacturing mixed with extensive professional riding experience. At the heart of Tannus is the patented Aither Technology; a multi-cell foam compound that forms the structure of the Armour. The inserts are designed to displace small impacts while offering a spring-like rebound for a smooth yet playful ride. - 3% Faster than standard tubeless - Flexible sidewall stabilizing "Wings" for smoother ride quality, with 50% more vibration damping - 20mm of rim protection - Not a sealant sponge – keeps sealant where it belongs - Easy Installation (5 Minutes, No tools required) - 150g - About as much as a standard tube (a little lighter)
$79.99
Tannus Armour Tubeless inserts are the result of years of top level multi-cell foam manufacturing mixed with extensive professional riding experience. At the heart of Tannus is the patented Aither Technology; a multi-cell foam compound that forms the structure of the Armour. The inserts are designed to displace small impacts while offering a spring-like rebound for a smooth yet playful ride. - 3% Faster than standard tubeless - Flexible sidewall stabilizing "Wings" for smoother ride quality, with 50% more vibration damping - 20mm of rim protection - Not a sealant sponge – keeps sealant where it belongs - Easy Installation (5 Minutes, No tools required) - 150g - About as much as a standard tube (a little lighter)
$79.50
Kit allows you to convert your Neo or Neo Ultimate hub. The thru-axle to QR kit includes two SealLock end caps and Stan's aluminum quick-release skewer. SealLock end caps feature a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. The QR/thru-axle to bolt-on kit includes end caps, threaded axle, bolts and washers. Bolt-on axles are recommended to prevent slipping and wheel misalignment in frames with horizontal drop-outs. - Not compatible with Centerlock or Boost hubs
$76.99
Replacement 9T sealed driver body for 49N sealed cartridge bearing rear 20 BMX wheel only (#247591-02). - Premium steel construction with 4-Pawl engagement (includes spring clip & pawls) - Includes x2 installed 6802 2RS sealed cartridge bearings - Weight: 103g
$76.99
- Hub axle end cap set, rear - Zipp Cognition V2 Rim Brake - Quick release
$75.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$75.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$75.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$75.99
Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.
$75.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$75.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$75.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$75.99
Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.
$75.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$75.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted. - DT Swiss Rear End Caps - QR x 135/142mm
$75.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$75.00
Adjustment clamps are used to adjust bearing preload on Chris King hubs. - Fits Chris King ISO SD Front, and Classic Rear
$74.99
Trainer ready. Keep the ride going by putting your Cannondale on a trainer with the 2-in-1 trainer axle. Where it thrives: The open road, on the trainer What it's built for: Versatility, convenience Highlights: - Fit your Cannondale road bike to any indoor trainer Removable end caps for outdoor riding - Compatible with Cannondale road bikes that utilize Speed Release dropouts
$74.99
Trainer ready. Keep the ride going by putting your Cannondale on a trainer with the 2-in-1 trainer axle. Where it thrives: The open road, on the trainer What it's built for: Versatility, convenience Highlights: - Fit your Cannondale road bike to any indoor trainer Removable end caps for outdoor riding - Compatible with Cannondale road bikes that utilize Syntace X-12 dropouts
$73.99
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$70.00
Convert Roval wheels with 142 or 142+ to be used with Boost spacing (110 /148mm) suspension forks and frames. - Kits include front and rear hub end caps, rotor spacers, and kit specific rotor bolts - Compatible with select MY13-16 Roval Wheels. Choose the appropriate SKU for each wheelset - Each conversion kit requires the existing rear wheel to be re-dished to center. Consult an authorized dealer to perform this operation
$66.99
Boostinator kits allow non-boost wheels to be mounted in Boost spacing frames and forks. While incremental, the benefits of the "Boost" 15x110mm front and 12x148mm rear axle standards are clear: better clearance for fatter tires & rims and reduced dish for stiffer, stronger wheels. The big bummer? Taking full advantage requires not only a new frame and fork, but new wheels as well. In response, we have developed the Boostinator. When paired with compatible 15x100mm or 12x142mm hubs, Boostinator kits allow existing wheels to be mounted in Boost-standard frames and forks. Disc and drivetrain positions are maintained and, thanks to a quick re-dish, spoke bracing angles are improved. Boostinator kits consist of a specially-designed axle end cap and, in the case of rear kits, a precision-machined rotor spacer with a set of six high-strength bolts. In keeping with Boost specifications, the disc and cassette are shifted outboard, allowing brakes and derailleurs to function as designed. Compatibility: - Front boostinators are only an endcap and do not require a rotor spacer. The wheel is re-dished. - Rear boostinators require both a re-dish and rotor spacer. - Rear Boostinator kits are not approved for rotors larger than 183mm. - Hubs spacing is 100mm front and 142 rear, and the Boostinators make them 110 and 148 respectively. - Compatible with 6-bolt FRONT wheels and SOME centerlock models. - Compatible with ONLY 6-bolt REAR wheels (there is no way to space centerlock rotors over 6mm). - NOT recommend (or safe) for non-symmetric lacing like the 2:1 lacing found on some of Industry Nine's wheels. *Note: You will need to re-dish your wheel after installing any Boosinator. Boostinator DR: - The Boostinator DR is compatible with DT-Swiss 12x142mm Star Ratchet (240- and 350-series) rear hubs with 6-bolt (IS) rotor mounts. - Centerlock hubs are not supported. - 180- and 190-series hubs are Centerlock only. - The Boostinator DR is also compatible with some complete wheels from DT Swiss, Roval (Specialized), Giant, Syncros (Scott), and others that use DT's Star Ratchet internals. - Remove the disc side end cap. Bearing size 6802 15x24. - Net weight: 18g Boostinator HR: - The Boostinator HR is compatible with 12x142mm Hope Pro 2 EVO and Pro 4 rear hubs. - Non-EVO Pro 2 hubs are not supported - Net weight: 18g Boostinator 9TR: - Compatible with 142x12 rear Industry Nine Torch hubs. - Not compatible with 2:1 lacing wheels from Industry Nine - Not compatible with Centerlock hubs Tech Specs: - Material: 6061 aluminum - Included: Rear kits come with appropriate-length Class 10.9 bolts, each roughly 40% stronger than more common Class 8.8 hardware.
$66.99
The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards
$65.95
The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA 7075 T6 Aluminum
$60.99
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 135mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 146mm - 1 axle per bag
$60.99
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese front hubs - Type: Hollow Axle - Threads: 9mm x 1 - Diameter: 9mm - Length: 110mm - 1 axle per bag
$60.99
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many BMX hubs - Type: Solid Axle - Threads: 9.5mm x 24tpi - Diameter: 9.5mm - Length: 180mm - 1 axle per bag
$59.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and to perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening
$59.99
The mounting solution for thru-bolt front wheels. Designed for an axle diameter of 9mm in the front, the thru-bolt system is a special kind of axle mounting for bikes. The DT Swiss thru-bolt system is compatible with standard quick-release dropouts but requires hubs that are compatible with the Thru Bolt. The stronger wheel connection results in greater stiffness. - Overall Length: 115mm - Thread Pitch: M9 x 1.0mm - Flat Washer
$59.99
Maximum stiffness and highest safety—the RWS Quick Release for road and MTB. Our patented RWS axle system is stiffer, safer, and easier to use than conventional quick-release axles. The RWS quick release is absolutely reliable and offers a strong connection to the frame. It's the perfect choice for anyone who is looking for maximum performance and safety.
$59.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening
$59.99
The mounting solution for Thru Bolt rear wheels. Designed for an axle diameter of 10mm in the rear, the thru bolt system is a special kind of axle mounting for bikes. The DT Swiss thru bolt system is compatible with standard quick-release dropouts, but requires matching hubs. The stronger wheel connection results in greater stiffness. - Overall Length: 152mm - Thread Pitch: M10 x 1.0mm - Flat Washer
$59.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - For E-thru axle frames - Length: 171mm - Thread Pitch: 12 x 1.5mm
$59.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Conical X12 washer, compatible with Syntace X-12 system - Thread Pitch: 12 x 1.0mm
$59.99
Maximum stiffness and highest safety—the RWS quick release for road and MTB. Our patented RWS axle system is stiffer, safer, and easier to use than conventional quick-release axles. The RWS quick release is absolutely reliable and offers a strong connection to the frame. The perfect choice for anyone who is looking for maximum performance and safety.
$57.99
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 126mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 137mm - 1 axle per bag
Page 1 of 4 Next page