Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

Robert Axle Project Trainer Thru Axle
$106.99
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
SRAM 9-10-11 Speed Freehub Body for 900 Rear Hub
$104.99
Original equipment freehub bodies to fit SRAM hubs and wheels.
Mavic ID360 Freehub Body V2
$99.99
Get rolling again with a replacement freehub body for your Mavic wheels. - For Mavic ID 360 hubs
Mavic XD Freehub Body
$99.99
Mavic's XD freehub body is compatible with all Crossmax and Deemax wheels (2012 and after) or all wheels using TS-2 hubs. This freehub body converts a rear wheel to work with SRAM's XD standard, making the wheel compatible with the XX1 drivetrain. Two kits are available : XD freehub body ITS-4 and XD freehub body TS-2, each with hub-specific parts.
Muc-Off Ultimate Tubeless Kit
$99.99
The Muc-Off Ultimate Tubeless Kit contains everything needed to get a tubeless-ready wheelset set up and ready to roll. Each Kit contains Tubeless Rim Tape, two CNC-machined black tubeless valves and two pouches of No Puncture Hassle Tubeless Sealant.
WeThePeople Cassette Hub Driver
$99.99
- Cassette Body Type: Single Cog Driver - Drivetrain Speeds: Single Speed 1/2" x 1/8" - Material: Steel - Tooth Count: 9
Robert Axle Project Rear Lightning Bolt-On Thru Axle
$94.99
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
Bontrager Ceramic Bearings
$54.99 - $89.99
- Grade 3 balls and magnetite rust proof finish - Abec 5 precision and silicone w seals - 3 times cryogenic race treatment - Bearings sold individually, not as pair
Mavic FTS-L 10-speed Freehub Body
$84.99 - $89.99
Get rolling again with a replacement 10-speed freehub body for Mavic wheels.
SRAM Maxle DH Front MTB
$87.99
Who knew we could make a thru axle disappear? The new Maxle Stealth offers a light, low profile alternative to Maxle Lite. - Hub OLD 20x110 - Length 158mm - Thread Length 10mm - Thread Pitch M20x1.50 - BoXXer C1 (2019+) - 34g lighter than Maxle Lite - Easy installation with a 6mm Allen wrench - Compatible with all 15mm forks
Robert Axle Project Front Lightning Bolt-On Thru Axle
$82.99
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
DT Swiss Pro Lock Aluminum Nipples
$81.49
The buyer's choice for wheel builders looking to save weight. ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond. - Weight: starting at 20g for 64 nipples
RockShox Maxle Ultimate Lever Assembly B1
$79.99
Maxle Ultimate Lever Assembly - Fits Maxle Ultimate B1 - Includes lever section only - Suitable for suspension forks
Stan's NoTubes Neo Conversion Kit
$79.50
Kit allows you to convert your Neo or Neo Ultimate hub. The thru-axle to QR kit includes two SealLock end caps and Stan's aluminum quick-release skewer. SealLock end caps feature a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. The QR/thru-axle to bolt-on kit includes end caps, threaded axle, bolts and washers. Bolt-on axles are recommended to prevent slipping and wheel misalignment in frames with horizontal drop-outs. - Not compatible with Centerlock or Boost hubs
DT Swiss RWS MTB Rear Thru Axle - X-12 System w/Plug-in Lever
$78.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Conical X12 washer, compatible with Syntace X-12 system - Removable, plug-in lever design is streamlined and protects your RWS lever - Thread Pitch: 12 x 1.0mm
DT Swiss RWS MTB Rear Thru Axle w/Plug-in Lever
$78.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Removable, plug-in lever design is streamlined and protects your RWS lever
49°N Replacement 9T Sealed Driver
$76.99
Replacement 9T sealed driver body for 49N sealed cartridge bearing rear 20 BMX wheel only (#247591-02). - Premium steel construction with 4-Pawl engagement (includes spring clip & pawls) - Includes x2 installed 6802 2RS sealed cartridge bearings - Weight: 103g
Profile Design Twenty-Four Series Quick Release Set
$76.99
Replacement road quick release skewer set (Front and Rear)
Wolf Tooth Components Fat Thru Axles
$75.99
The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum
Chris King High Profile Adjustment Clamp
$75.00
Adjustment clamps are used to adjust bearing preload on Chris King hubs. - Includes one High Profile (HP) Adjustment Clamp - Fits all Chris King ISO/Disc Rear Hubs
Chris King Low Profile Adjustment Clamp
$75.00
Adjustment clamps are used to adjust bearing preload on Chris King hubs. - Fits Chris King ISO SD Front, and Classic Rear
Cannondale 2-in-1 Speed Release Trainer Axle
$74.99
Trainer ready. Keep the ride going by putting your Cannondale on a trainer with the 2-in-1 trainer axle. Where it thrives: The open road, on the trainer What it's built for: Versatility, convenience Highlights: - Fit your Cannondale road bike to any indoor trainer Removable end caps for outdoor riding - Compatible with Cannondale road bikes that utilize Speed Release dropouts
Cannondale 2-in-1 Syntace Trainer Axle
$74.99
Trainer ready. Keep the ride going by putting your Cannondale on a trainer with the 2-in-1 trainer axle. Where it thrives: The open road, on the trainer What it's built for: Versatility, convenience Highlights: - Fit your Cannondale road bike to any indoor trainer Removable end caps for outdoor riding - Compatible with Cannondale road bikes that utilize Syntace X-12 dropouts
Roval Boost Conversion Kit
$74.99
Convert Roval wheels with 142 or 142+ to be used with Boost spacing (110 /148mm) suspension forks and frames. - Kits include front and rear hub end caps, rotor spacers, and kit specific rotor bolts - Compatible with select MY13-16 Roval Wheels. Choose the appropriate SKU for each wheelset - Each conversion kit requires the existing rear wheel to be re-dished to center. Consult an authorized dealer to perform this operation
Shimano 105 5800 Freehub Body
$73.99
- Cassette Body Type: Shimano/SRAM 11 Speed Road - Material: Steel
DT Swiss Standard Aluminum Nipples
$24.69 - $67.39
The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples
Wolf Tooth Components 12mm Rear Thru Axle
$66.99
The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards
Wolf Tooth Components 15mm Road Front Thru Axle
$66.99
The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA 7075 T6 Aluminum
Wolf Tooth Components FOX Front Thru Axle
$66.99
The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA - 7075 T6 Aluminum - Similar to Fox Kabolt axle
Wolf Tooth Components Rear Boostinator
$66.99
Boostinator kits allow non-boost wheels to be mounted in Boost spacing frames and forks. While incremental, the benefits of the "Boost" 15x110mm front and 12x148mm rear axle standards are clear: better clearance for fatter tires & rims and reduced dish for stiffer, stronger wheels. The big bummer? Taking full advantage requires not only a new frame and fork, but new wheels as well. In response, we have developed the Boostinator. When paired with compatible 15x100mm or 12x142mm hubs, Boostinator kits allow existing wheels to be mounted in Boost-standard frames and forks. Disc and drivetrain positions are maintained and, thanks to a quick re-dish, spoke bracing angles are improved. Boostinator kits consist of a specially-designed axle end cap and, in the case of rear kits, a precision-machined rotor spacer with a set of six high-strength bolts. In keeping with Boost specifications, the disc and cassette are shifted outboard, allowing brakes and derailleurs to function as designed. Compatibility: - Front boostinators are only an endcap and do not require a rotor spacer. The wheel is re-dished. - Rear boostinators require both a re-dish and rotor spacer. - Rear Boostinator kits are not approved for rotors larger than 183mm. - Hubs spacing is 100mm front and 142 rear, and the Boostinators make them 110 and 148 respectively. - Compatible with 6-bolt FRONT wheels and SOME centerlock models. - Compatible with ONLY 6-bolt REAR wheels (there is no way to space centerlock rotors over 6mm). - NOT recommend (or safe) for non-symmetric lacing like the 2:1 lacing found on some of Industry Nine's wheels. *Note: You will need to re-dish your wheel after installing any Boosinator. Boostinator DR: - The Boostinator DR is compatible with DT-Swiss 12x142mm Star Ratchet (240- and 350-series) rear hubs with 6-bolt (IS) rotor mounts. - Centerlock hubs are not supported. - 180- and 190-series hubs are Centerlock only. - The Boostinator DR is also compatible with some complete wheels from DT Swiss, Roval (Specialized), Giant, Syncros (Scott), and others that use DT's Star Ratchet internals. - Remove the disc side end cap. Bearing size 6802 15x24. - Net weight: 18g Boostinator HR: - The Boostinator HR is compatible with 12x142mm Hope Pro 2 EVO and Pro 4 rear hubs. - Non-EVO Pro 2 hubs are not supported - Net weight: 18g Boostinator 9TR: - Compatible with 142x12 rear Industry Nine Torch hubs. - Not compatible with 2:1 lacing wheels from Industry Nine - Not compatible with Centerlock hubs Tech Specs: - Material: 6061 aluminum - Included: Rear kits come with appropriate-length Class 10.9 bolts, each roughly 40% stronger than more common Class 8.8 hardware.