Fenders

- Spoiler/lower fender - 35mm fits 35 Chromoplastics, Commuter II & Raceblade fenders - Hardware included

Addd an extra dose of stability to SKS's Velo 42 and Velo 47 fenders. A stainless steel U-stay mounts to the fenders and your frame eyelets to eliminate rattling and bouncing fenders.

Stay clean and dry with SKS's Velo42 Urban fenders! The rear snap-on fender attaches to seat tubes between 25 and 35mm in diameter to give you full coverage from road spray. These fenders fit tires up to 32mm wide.

The VELOFLEXX mudguard set combines the stability of a fixed mudguard with the flexibility of a clip-on mudguard. The VELOFLEXX bridge allows the rear mudguard to be attached at the top of the seat stay with the use of rubber straps—no tools needed. This method of mounting doesn't rely on the cross stay where the caliper brake is usually bolted. At the front, the VELOFLEXX is mounted to the fork bridge with a rubberized hook-and-loop fastener or a cable tie. The black-coated stays provide even greater support. - Compatible only with disc brakes - Includes hook-and-loop fasteners and tension rubber

The X-Blade 26/27.5-inch is a high-quality 2-component fender for the rear wheel of mountain and trekking bikes. Due to the quick-release mounting, the fender can be fitted to almost any seat post and optimally adjusted to the wheel using the 2-joint technology. - High performance dual compound plastic - Easy quick-release-fastening by pre-adjusted powerstrap - 2 joints for optimized adjustment to all frames - Optimized dirt protection - 26-inch and 27.5-inch wheel compatible

The X-Board is an innovative clip-on fender with rubber fasteners for downtube mounting. - Adjustable soft rubber cable-spacers, ideal to adapt on almost any tube profile - Robust rubber fasteners - Dual compound-softspoiler

The X-Guard is a universal downtube fender for any wheel size. It is attached using two straps on the lower bar (downtube), making it compatible with fat bikes and bicycles with oversized tires for all-around mud protection. It also protects E-MTB batteries from dirt, splashes and flying rocks. The straps are extra long and can be shortened as needed, making X-Guard suitable for any frame shape and all common battery models.

X-Long Mudflap/Spoiler can be retrofitted to any fender profile of the correct size. A hole may need to be drilled in the profile if one isn't already there. - Adds 6 inches of coverage to any fender profile - 35mm size fits fender profiles up to 35mm - 53mm size fits fender profiles 46mm-55mm

The X-Long Spoiler is designed to add extra coverage to SKS fenders. - Compatible with 45mm versions of the Chromoplastic, Commuter II, Long Board and Raceblade fender models - Easily mounted by consumer with included hardware - Sold as Each

Optimized for RockShox forks, RockShox MTB Fenders deliver exceptional protection for your fork with deep side skirts to keep the mud and debris away from the most vital parts of your fork—and your body. Take your bike's customization to the next level with color offerings made to match RockShox decal packs—or go black-on-black for that minimalist look. MTB Fenders come complete with four beefy zip ties for installation, so you can get to the trailhead sooner and shred with much less mess. - Works on all RockShox fork models - Comes with 4 zip ties for immediate installation - Offered in a wide range of colors that match RockShox's fork decal packs - Deep side skirts protect stanchions and dust seals from rocks and debris

Optimized for RockShox forks, RockShox MTB Fenders deliver exceptional protection for your fork, with deep side skirts to keep the mud and debris away from the most vital parts of your fork—and your body. Take your bike's customization to the next level with nine color offerings made to match RockShox decal packs—or go black-on-black for that minimalist look. MTB Fenders come complete with four beefy zip ties for installation so you can get to the trailhead sooner and shred with much less mess. - Works on all RockShox fork models - Comes with 4 zip ties for immediate installation - Offered in a wide range of colors that match RockShox's fork decal packs - Designed specifically for RockShox forks - Deep side skirts protect stanchions and dust seals from rocks and debris - Precisely placed mounting holes make the fender follow the wheel's contour, minimizing contact when the fork is compressed

Gravel away in rain, show, sleet or shine. The new RockShox premium short fender is designed to keep you dry and clean when the weather turns. It can be easily installed at 3-bolt mounts and looks as if your fork and fender are one, leaving your friends wondering why they are still messing around with zip ties. - 3-bolt mounts ensures secure attachment - Designed to integrate seamlessly and look pro with RockShox branding - Compatible with all Rudy XPLR models

- Adapts to 24'' or 26'' wheels - Made of shock resistant polymer

- Can be used on 24'' or 26'' wheels - Designed specially for use with V-brakes and bike with suspension - Mounting kit included - Adjustable L shape steel bracket for rear and front mudguard - Made of shock resistant polymer - 100% recyclable material - Reflective safety stickers mounting

- Fits tubes from Ø27 to 35mm - Fits 26" to 28" wheels - Two width options: 51mm and 46mm - Front mudguard compatible with disc brakes or V-Brake, and suspension or rigid bikes - Expander range on front and rear for perfect fitting - Adjustable L shape steel bracket for rear and front mudguard - For an extra secure mounting of the rear mudguard we also offer a Ø 3 mm stainless steel U-stay - Mounting kit included

- Fits tubes from Ø27 to 35mm - Fits 26" to 29" wheels - Mudguard section of 55mm - Front mudguard compatible with disc brakes or V-Brake, and suspension or rigid bikes - Expander range on front and rear for perfect fitting - Includes long and short clamp depending on the space needed to clip it to the frame - Adjustable L shape steel bracket for rear and front mudguard - For an extra secure mounting of the rear mudguard we also offer a Ø 3 mm stainless steel U-stay - Mounting kit included

- Fits tubes from Ø27 to 35mm - Fits 20" to 24" wheels - Mudguard section of 55mm - Front mudguard compatible with disc brakes or V-Brake, and suspension or rigid bikes - Expander range on front and rear for perfect fitting - Includes long and short clamp depending on the space needed to clip it to the frame - Adjustable L shape steel bracket for rear and front mudguard - Mounting kit included

- Adapts to 700C wheels - Made of shock resistant polymer

The new EVO bolt-on fender is designed around the latest FOX 36 and 38 forks, to avoid the problem of the crown hitting the mudguard at full compression (minimum Fork Offset: 44mm). Fender bolts directly to the back of the fork brace. Supplied with rubber pads, bolts, washers and hex key to install to your FOX forks. Compatible with older (2017) onwards FOX 34 & 36 forks which have bolt holes in the brace. Also compatible with the fork brands below (separate adapter kits are required): - Rock Shox Zeb - Rock Shox Recon Gold or Silver 35 - DVO Onyx SC, Sapphire, & Diamond - Ohlins RXF 38 (2019+) & DH - Total length: 515mm (Rr extension 330mm, Fr extension 185mm) - More mud clearance - No more crown fouling at full compression - Stiffer, optimum length, not too short, no longer than needed - Designed and made in the UK from recycled PP - 125g

The new EVO fender was designed around the latest FOX 36 and 38 forks, to avoid the problem of the crown hitting the mudguard at full compression. The EVO Ziptie fender attaches directly to the fork with the supplied zip-ties. Compatible with most forks other than models with reverse arch. - Total length: 515mm (Rr extension 330mm, Fr extension 185mm) - More mud clearance - No more crown fouling at full compression - Stiffer, optimum length, not too short, no longer than needed - Designed and made in the UK from recycled PP - Strong enough for DH racing at the highest level - 120g

Following the tried and tested tire-hugging design of our MTB Mudhuggers, the GravelHugger is designed to fit most fork + wheel + tire (up to 50mm wide) combos. To reduce single-use plastic waste, and make fitting and removing easier, the GravelHugger is supplied with nitrile O-rings (70mm sizes for flat blade type and 50mm for traditional round steel forks). Zip ties (sold separately) can be utilized if you'd prefer to fit and leave them on at all times. - Suitable for 700c (Max tire width 42mm) and 650b wheels (Max tire width 50mm), depending on wheel/tire/fork combination - Designed and made in the UK from 100% recycled polypropylene - Includes Helitape and nitrile O-rings - Length: 490mm - Width: 60mm - Weight: 75g

The new Shorty EVO bolt-on fender is designed around the latest FOX 36 and 38 forks, to avoid the problem of the crown hitting the mudguard at full compression (minimum Fork Offset: 44mm). Fender bolts directly to the back of the fork brace. Supplied with rubber pads, bolts, washers, and hex key to install to your FOX forks. Compatible with older (2017) onwards FOX 34 & 36 forks that have bolt holes in the brace. Also compatible with the fork brands below (separate adapter kits are required): - Rock Shox Zeb - Rock Shox Recon Gold or Silver 35 - DVO Onyx SC, Sapphire, & Diamond - Ohlins RXF 38 (2019+) & DH - Total length: 390mm (Rr extension 255mm, Fr extension 105mm) - More mud clearance - No more crown fouling at full compression - Stiffer, optimum length, not too short, no longer than needed - Designed and made in the UK from recycled PP - 100g

- Technopolymer construction - Durable and weatherproof material - Fits most front forks - Zip ties included

- TPR mud flap - Compatible for 24'' to 26'' wheels - Quick mount system

- Made of resistant chromoplastic - Stainless steel bracket and stays - Pre-assembled for fast and easy installation

An innovative adapter that adds eyelets to any QR-equipped bike, facilitating the mounting of traditional fenders to bicycles lacking front and rear eyelets. CONSTRUCTION • Lightweight red anodized aluminum MOUNTING SYSTEM • Mount to quick release skewer ADDED BENEFIT • A quick and easy solution to make fenders fit • Set of four

A sturdy, secure set of full-coverage fenders designed to fit more bikes than any fenders in their class. Easy to install and easy to adjust, Roadrunners are a favorite of both cyclists and shop mechanics. Weight: 652 g / 1.44 lbs (pair) Construction - Forged alloy RAINRUNNER Q/R mounts - 3M Reflex rear reflectivity - Virtually unbreakable Techniflex body - Stainless steel stays - Safety front stays Mounting System - Below: Mount to Quick-Release skewers via included AXLE-RUNNERS - Above: Mount to brake bridge and fork crown via included nut and bolt or with zip ties Added Benefit - Included proprietary AXLE-RUNNERS mount to almost any front or rear Q/R skewer to “create” eyelets - 3M Reflex rear logo enhances visibility - Support stays spaced for maximum stiffness and frame compatibility - Front fenders equipped with safety stays to protect against objects becoming lodged in wheel - Sold pre-assembled for quick mounting

A sturdy, secure set of full-coverage fenders designed to fit more bikes than any fenders in their class. Easy to install and easy to adjust, Roadrunners are a favorite of both cyclists and shop mechanics. Weight: 752 g / 1.66 lbs (pair) Construction - Forged alloy RAINRUNNER Q/R mounts - 3M Reflex rear reflectivity - Virtually unbreakable Techniflex body - Stainless steel stays - Safety front stays Mounting System - Below: Mount to Quick-Release skewers via included AXLE-RUNNERS - Above: Mount to brake bridge and fork crown via included nut and bolt or with zip ties Added Benefit - Included proprietary AXLE-RUNNERS mount to almost any front or rear Q/R skewer to “create” eyelets - 3M Reflex rear logo enhances visibility - Support stays spaced for maximum stiffness and frame compatibility - Front fenders equipped with safety stays to protect against objects becoming lodged in wheel - Sold pre-assembled for quick mounting

A sturdy, secure set of full-coverage fenders designed to fit more bikes than any fenders in their class. Easy to install and easy to adjust, Roadrunners are a favorite of both cyclists and shop mechanics. Weight: 606 g / 1.34 lbs (pair) Construction -Forged alloy RAINRUNNER Q/R mounts - 3M Reflex rear reflectivity - Virtually unbreakable Techniflex body - Stainless steel stays - Safety front stays Mounting System Below: Mount to Quick-Release skewers via included AXLE-RUNNERS Above: Mount to brake bridge and fork crown via included nut and bolt or with zip ties Added Benefit - Included proprietary AXLE-RUNNERS mount to almost any front or rear Q/R skewer to “create” eyelets - 3M Reflex rear logo enhances visibility - Support stays spaced for maximum stiffness and frame compatibility - Front fenders equipped with safety stays to protect against objects becoming lodged in wheel - Sold pre-assembled for quick mounting

Versatile, flexible, front fender for mountain bikes. Fits virtually any fork with arch in front and any tire diameter with width up to 3.0". - Slop Stop - The Slop Stop leading edge catches mud and water the tire picks up and flings forward. Catching this slop at the tire helps prevent it from getting blown into your face! - Seal Shield - The Seal Shield drop section wings provide an effective barrier to trail debris and muck, helping keep your fork seals cleaner longer. - Flop Stop - The Flop Stop rear section's carefully engineered fold provide stiffness. This stiffness prevents the fender from contacting the front wheel and getting sucked into the fork, stopping you in a hurry! The folds also contour the fender around the tire making it a better mud guard. - Includes 4 reusable zip ties - Weight: 27g

The LARGE Rear Mudhugger has been designed around the Specialized Turbo Levo for todays slack and long 29ers and 650B bikes. The LARGE Rear Mudhugger is an all new design for the modern full suspension bikes that have low seat stay angles of 27 deg down to 22 deg. This is an extra long Hugger that is designed to be trimmed down to fit your bike perfectly. Think Specialized Turbo Levo, Kenevo, most Pivot, Nukeproof bikes, Santa Cruz, Lapierre, 2020 Canyon and Yeti full suss bikes. However, it will work well on bikes with 27-28 degree seat stays, but will be too long and need the end trimmed shorter still. The rear fender braces are designed to be custom-cut around cable stops/guides and other unique seatstay/swingarm shapes and features. Some frames have assymetrical stays, like found on EVIL bikes, and may not fit or will require extensive customization to fit. Kit includes fender, zipties and protective heli tape. Ideal for all 29" and 27.5+ full suspension bikes. Approx 760 mm long. Approx 105mm wide at the widest part. Braces are approx 160mm long. Weight approx 280g exc fittings. Includes frame tape and 6 zipties. Initially designed to overcome the problem of fitting mudguards to a bike with a dropper seat post the Rear Mudhugger works well on all bikes, providing they have disc brakes. However, attaching the Hugger to the seat stays also overcomes all of the problems normally associated with rear mudguards. They do not move out of line, get in the way getting on or off the bike, do not foul rear suspension travel, and are robust enough to take the rough and tumble of modern trail riding demands. Developed during the wettest UK summer on record the Huggers have been praised by many of the major bike magazines for their simplicity and effectiveness in back to back tests with other mudguards. Whilst we’d be the first to admit we wouldn’t win any beauty competitions, once fitted to your bike you will hardly notice it’s there, and staying dryer and cleaner for longer means you can stay out on your bike for longer before retiring to the pub for a well earned pint or 2... remember, always drink responsibly ;) For those of you into your DH, enduro or endurance racing, being able to get out in all weather conditions, train hard and remain comfortable for much longer will undoubtedly pay dividends at the start of the race season.